lohaexplore.blogg.se

Verifone model vx-usb-rs232 drivers for ubuntu
Verifone model vx-usb-rs232 drivers for ubuntu










verifone model vx-usb-rs232 drivers for ubuntu
  1. #VERIFONE MODEL VX USB RS232 DRIVERS FOR UBUNTU HOW TO#
  2. #VERIFONE MODEL VX USB RS232 DRIVERS FOR UBUNTU SERIAL#
  3. #VERIFONE MODEL VX USB RS232 DRIVERS FOR UBUNTU DRIVER#

> number and product number to tell the usbserial > Now, we need to figure out the device vendor > usb 1-1: configuration #1 chosen from 1 choice > usb 1-1: new full speed USB device using uhci_and > Torward the end of the messages, you should see > device, first check the hardware messages to see

#VERIFONE MODEL VX USB RS232 DRIVERS FOR UBUNTU SERIAL#

> serial drivers may need to be installed for the > If you are using the usb -> RS232 adapter, the > BOM wasn't in the wiki - nor was it immediately > The procedure for using the USB adapter from the

#VERIFONE MODEL VX USB RS232 DRIVERS FOR UBUNTU HOW TO#

usb 4-1: can't set config #1, error -32Ĭan you tell me how to detect the adpater

verifone model vx-usb-rs232 drivers for ubuntu

usb 4-1: configuration #1 chosen from 1 choice usb 4-1: new full speed USB device using uhci_hcd and address 6 hub 4-0:1.0: unable to enumerate USB device on port 1 usb 4-1: device descriptor read/all, error -32 usb 4-1: device descriptor read/8, error -32 usb 4-1: new full speed USB device using uhci_hcd and address 5 usb 4-1: new full speed USB device using uhci_hcd and address 4 usb 4-1: device descriptor read/all, error -84 usb 4-1: new full speed USB device using uhci_hcd and address 3 usb 4-1: can't read configurations, error -84 usb 4-1: unable to read config index 0 descriptor/all usb 4-1: new full speed USB device using uhci_hcd and address 2 Last edit at 02:01AM by Freeman.Īnd done dmesg, it shows the following error : Now, you should have no problem using this device for RepRap like a normal serial port. To /etc/modules with the vendor and product numbers you found. As much fun as you had doing this, there is some chance you want to do this automatically in the future.

#VERIFONE MODEL VX USB RS232 DRIVERS FOR UBUNTU DRIVER#

Usbcore: registered new interface driver usbserial_genericĬongratulations, your link is up - in this example, the device can be used on /dev/ttyUSB0. Usb 1-1: generic converter now attached to ttyUSB0 Usbserial_generic 1-1:1.0: generic converter detected Near the end, you should see something like: Sudo modprobe usbserial vendor=0x4348 product=0x5523įinally, check dmesg again to ensure it loaded properly. Now, we can load up the driver for this device: Which returns the summary list again, but now showing the new USB device: Now, plug the device back in, and run lsusb again: You will see a summary list of your USB devices on the system, I only have one: The easiest way to find the information is to first unplug the device, then run lsusb: Now, we need to figure out the device vendor number and product number to tell the usbserial driver. Usb 1-1: configuration #1 chosen from 1 choice Usb 1-1: new full speed USB device using uhci_and address 2 Torward the end of the messages, you should see this: After plugging in the device, first check the hardware messages to see the device was detected: If you are using the usb -> RS232 adapter, the serial drivers may need to be installed for the device to work properly. The procedure for using the USB adapter from the BOM wasn't in the wiki - nor was it immediately obvious, so, here goes.












Verifone model vx-usb-rs232 drivers for ubuntu